Flange_bOne-dimensional translational flange (right, flange axis directed OUT OF cut plane) |
 |
Information
This information is part of the Modelica Standard Library maintained by the Modelica Association.
This is a connector for 1-dim. translational mechanical systems which represents a mechanical flange. In the cut plane of the flange a unit vector n, called flange axis, is defined which is directed OUT OF the cut plane. All vectors in the cut plane are resolved with respect to this unit vector. E.g. force f characterizes a vector which is directed in the direction of n with value equal to f. When this flange is connected to other 1D translational flanges, this means that the axes vectors of the connected flanges are identical.
The following variables are transported through this connector:
s: Absolute position of the flange in [m]. A positive translation means that the flange is translated along the flange axis. f: Cut-force in direction of the flange axis in [N].
Used in Components (31)
 |
Modelica.Electrical.Analog.Basic Electromotoric force (electric/mechanic transformer) |
 |
Modelica.Magnetic.FluxTubes.Examples.MovingCoilActuator.Components Detailed actuator model for rough magnetic design of actuator and system simulation |
 |
Modelica.Magnetic.FluxTubes.Examples.MovingCoilActuator.Components Simple behavioural actuator model for system simulation |
 |
Modelica.Magnetic.FluxTubes.Examples.SolenoidActuator.Components Simple network model of a lifting magnet with planar armature end face |
 |
Modelica.Magnetic.FluxTubes.Examples.SolenoidActuator.Components Advanced network model of a lifting magnet with planar armature end face, split magnetomotive force |
 |
Modelica.Magnetic.FluxTubes.Examples.Utilities Mass with free travel between two stoppers |
 |
Modelica.Magnetic.FluxTubes.Interfaces Base class for flux tubes with reluctance force generation; constant permeability |
 |
Modelica.Mechanics.MultiBody.Forces General line force component with an optional point mass on the connection line |
 |
Modelica.Mechanics.MultiBody.Forces General line force component with two optional point masses on the connection line |
 |
Modelica.Mechanics.MultiBody.Joints Prismatic joint (1 translational degree-of-freedom, 2 potential states, optional axis flange) |
 |
Modelica.Mechanics.MultiBody.Joints.Assemblies Universal - prismatic - spherical joint aggregation (no constraints, no potential states) |
 |
Modelica.Mechanics.MultiBody.Joints.Assemblies Universal - spherical - prismatic joint aggregation (no constraints, no potential states) |
 |
Modelica.Mechanics.MultiBody.Joints.Assemblies Spherical - spherical - prismatic joint aggregation with mass (no constraints, no potential states) |
 |
Modelica.Mechanics.MultiBody.Joints.Assemblies Planar revolute - revolute - prismatic joint aggregation (no constraints, no potential states) |
 |
Modelica.Mechanics.MultiBody.Joints.Internal Prismatic joint where the translational distance is computed from a length constraint (1 degree-of-freedom, no potential state) |
 |
PartialElementaryRotationalToTranslational Modelica.Mechanics.Rotational.Interfaces Partial model to transform rotational into translational motion |
 |
Modelica.Mechanics.Translational.Components Fixed flange |
 |
Modelica.Mechanics.Translational.Components Initializes a flange with pre-defined position, speed and acceleration (usually, this is reference data from a control bus) |
 |
Modelica.Mechanics.Translational.Components Signal adaptor for a Translational flange with force as output and position, speed and acceleration as input (especially useful for FMUs) |
 |
Modelica.Mechanics.Translational.Interfaces Component with two translational 1D flanges |
 |
Modelica.Mechanics.Translational.Interfaces Partial model for a component with one translational 1-dim. shaft flange and a support used for graphical modeling, i.e., the model is build up by drag-and-drop from elementary components |
 |
Modelica.Mechanics.Translational.Interfaces Partial model for a component with two translational 1-dim. shaft flanges and a support used for graphical modeling, i.e., the model is build up by drag-and-drop from elementary components |
 |
Modelica.Mechanics.Translational.Interfaces Rigid connection of two translational 1D flanges |
 |
Modelica.Mechanics.Translational.Interfaces Compliant connection of two translational 1D flanges |
 |
PartialCompliantWithRelativeStates Modelica.Mechanics.Translational.Interfaces Base model for the compliant connection of two translational 1-dim. shaft flanges where the relative position and relative velocities are used as states |
 |
PartialElementaryOneFlangeAndSupport Modelica.Mechanics.Translational.Interfaces Obsolete partial model. Use PartialElementaryOneFlangeAndSupport2. |
 |
PartialElementaryOneFlangeAndSupport2 Modelica.Mechanics.Translational.Interfaces Partial model for a component with one translational 1-dim. shaft flange and a support used for textual modeling, i.e., for elementary models |
 |
PartialElementaryTwoFlangesAndSupport Modelica.Mechanics.Translational.Interfaces Obsolete partial model. Use PartialElementaryTwoFlangesAndSupport2. |
 |
PartialElementaryTwoFlangesAndSupport2 Modelica.Mechanics.Translational.Interfaces Partial model for a component with one translational 1-dim. shaft flange and a support used for textual modeling, i.e., for elementary models |
 |
Modelica.Mechanics.Translational.Interfaces Device to measure a single relative variable between two flanges |
 |
Modelica.Fluid.Machines varying cylindric volume depending on the position of the piston |